You want to build the model that you have to choose and decide how and where it will be displayed. The tools to plan, and reference material needs and a safe working area will be created for himself is collected. You are almost ready to begin.
Building jig; model before actual construction started, there is a preparation to carry out work. Jig to the work during construction to provide a stable base with the model while still holding the modeler is working on it. There are two types of jigs are that you will find useful. Jig temporary and permanent display stand.
Floating jigs are either commercially available or model builder can build your own. Commercially available jigs Fair-A-frame to the false keel bulkheads used to ensure the correct alignment, the hull planking screws allow the liars on the stand builder model inversion point, holds a wooden conical device, such devices are the hull planking and keel Klamper vice president who screws like the hull planking many builders making it easier to rotate towards making the model with the convenience of allowing, but similar functions. With any of these jigs, models built on the Jig can stay during the competition.
To make your own jig, the base plate "glue paper or plastic film-based. Thick, somewhat longer and wider than ¾ of the ship hull on a sheet of chipboard should be, and the right of the ship Drawing centerline and exact location of the frame - then you will appreciate these lines: you have a small plumb bob or a class by using tell whether false keel bulkheads are at right angles will be able to actually stem and stern the supports. base plates at 90 degrees to ensure that the keel, hard, and should sternpost are all standing again to check what you frame the center of the beam center and mid-ship flight deck are Exxon allows. by using a small plumb bob. supports can be made of wood, but angle iron is better. model to the jig Wales have begun building the hull is very hard to stay panel can be removed from the stage model. will.
Panel, staining, painting and underwater hull coppering (if appropriate) after it makes sense to fix a permanent display stand models. Base plate of the stand should be made of a high quality hardwood for the model as appropriate. Choice of wood is all a matter of taste, but it should harmonize with the colors of ship models. Standing not far from the viewer should draw the attention of the model itself. An example, oak, walnut or mahogany only as much of the 19th century with dark planked vessels should be. Suffered damage during the base plate to prevent further construction, it covered with a sheet of thick plastic and tape the edges to secure.
cradles, pedestals, and block, there are three types of model display stands. Dioramas also saw some time with slipways holding up models.
Never the way you display your model, make sure to safely stand and model itself is attached to the base board to choose. Gluing is good screwing better. The advantage of bringing the model builders are ensuring security and peace of mind; disadvantage that the two places, the underwater hull lines are interrupted. Incidentally, the support cradle for the hull surfaces must be an exact fit. The advantage of the helm seat as it has been shown to maximum effect, the damage that you drill a hole in the keel of the model. Back should not be too long - maybe 1 "to 2 ½ inches - then you do not want to distract from the ship models.
There are other jigs are a number of you will find helpful. Deck planking, it is useful to create a cutting template so that all are equal in length and an overlay pattern that toenails are lined up properly. More later on the subject.
Bending wood, once again there commercially available jigs and tools. A panel machine to stick to an unspecified degree turn, but the piece will create more flexible. Different shapes and angles to make a point jig allows the tool itself is adjustable. It is a piece of wood that are good for up to 0.8mm thick. Then Bender electric point, the thicker pieces of wood allows for very severe bends. This tool is excellent for the early period of ship modeling. There are hand tools available that work by notching the wood to bend to allow a number that are. You also bending jig from a scrap piece of plywood and nails made of wood can. Arrangement of nails in a crescent shape, cover them with tape (to avoid rusting) and jig to dry your wet ingredients panel space. It is effective for schooners like the hull shapes.
Wednesday, October 20, 2010
Subscribe to:
Posts (Atom)